If a new component would be installed, there are procedures for that which you need to bear in mind. The procedures have to be followed to install Profile Design Cobra bars properly. That is also a requirement on the policy for the warranty that is provided when you buy one. When you are now knowledgeable on such task, go to its dealer near the area.
There is a manual that contains the methods on how it should be done. When you have decided to do it yourself, you have to prepare the tools that you would be using for it. You should have Allen wrenches or torque wrenches. You should also have sandpaper as it would be used in making it smooth. When you have prepared all of it, you can now start with it.
You should avoid greasing the clamping area. If you would be greasing it, it would only cause the bar to slip from it. You have to make sure that such situation would not happen especially when you are already using your bike. It would cause you to lose control while you are riding the bike. It would be very dangerous on your part if that would happen.
You have to ensure that its bar clamp diameter would be suitable on its stem diameter. That has to be inspected as it will surely cause a lot of issues in the future. They would not be fit together when their diameters are different. Before an item is purchased, you must look at its diameter for you to prevent any waste of cash on the purchase you would be making.
If one is going to install a stem which is new, the manufacturer also provides an instruction for that. The manufacturer would set the procedures on how a person will have the capability to properly do such task. That is stated on a manual which has been given to him so he is not going to experience any difficulties while he is going to do this.
You should check the front stem clamp if there are any sharp edges. Use the sandpaper that you have so that they would be removed. You have to do that as it would damage the fiber of the aluminum or carbon. Once you have placed it on its position, you could now clamp it on the stem. You have to make sure that it is tight.
You could slide a level to its bar. You could make some adjustments based on your preference when you are uncomfortable with it. This must be placed cautiously. You must bear in mind that the warranty will be invalid when it is broken.
It can be wrap if you prefer that. When you try this, you must ensure that a helmet would be worn. Inspect if it will function properly prior to the time you will be utilizing it on longer distances.
It is essential that those steps will be followed. This will be risky on you as you will lose your control on that bike. It could cause worst injuries on a person.
There is a manual that contains the methods on how it should be done. When you have decided to do it yourself, you have to prepare the tools that you would be using for it. You should have Allen wrenches or torque wrenches. You should also have sandpaper as it would be used in making it smooth. When you have prepared all of it, you can now start with it.
You should avoid greasing the clamping area. If you would be greasing it, it would only cause the bar to slip from it. You have to make sure that such situation would not happen especially when you are already using your bike. It would cause you to lose control while you are riding the bike. It would be very dangerous on your part if that would happen.
You have to ensure that its bar clamp diameter would be suitable on its stem diameter. That has to be inspected as it will surely cause a lot of issues in the future. They would not be fit together when their diameters are different. Before an item is purchased, you must look at its diameter for you to prevent any waste of cash on the purchase you would be making.
If one is going to install a stem which is new, the manufacturer also provides an instruction for that. The manufacturer would set the procedures on how a person will have the capability to properly do such task. That is stated on a manual which has been given to him so he is not going to experience any difficulties while he is going to do this.
You should check the front stem clamp if there are any sharp edges. Use the sandpaper that you have so that they would be removed. You have to do that as it would damage the fiber of the aluminum or carbon. Once you have placed it on its position, you could now clamp it on the stem. You have to make sure that it is tight.
You could slide a level to its bar. You could make some adjustments based on your preference when you are uncomfortable with it. This must be placed cautiously. You must bear in mind that the warranty will be invalid when it is broken.
It can be wrap if you prefer that. When you try this, you must ensure that a helmet would be worn. Inspect if it will function properly prior to the time you will be utilizing it on longer distances.
It is essential that those steps will be followed. This will be risky on you as you will lose your control on that bike. It could cause worst injuries on a person.
About the Author:
When you are looking for information about Profile Design Cobra Bars go to the web pages online here today. You can see details at http://www.sportfactoryproshop.com now.
No comments:
Post a Comment